Etc Sensor3 CE (ESR3) Rack Instrukcja Użytkownika Strona 32
- Strona / 48
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
24 Sensor3 CE Rack (ESR3) Installation Manual
Dual Tracking Remote Select Switch connection (Optional)
If desired, a remote switch can be wired to the CEM3 backplane to control CEM3 selection
in racks equipped with ETC’s Redundant Tracking CEM3 option.
Step 1: Pull 1.5mm
2
wires between your remote switch and the CEM3 backplane
through the data cable conduit. See Running DMX Cable to Racks, page 20 for
data conduit installation details. For systems with no requirement for remote
tracking status indication three wires are required, otherwise four wires will be
required.
Step 2: Connect the remote switch wires to the J12 connector on the rear of the
backplane.
Step 3: Wire the remote switch and indicator to the J12 connector according to
Figure 26.
Note:
You must supply your own enclosed single-pole double-throw center-off switch to
install a remote select switch. You may optionally use an external 24V DC power
supply, or use the power supply from the rack backplane.
Note:
The J12 connector is a removable plug header and is easier to wire when it is
disconnected from the backplane in an installed rack.
1 2 3 4+24Vdc COM
J12
Figure 26: J12 Dual Tracking remote connector wiring
Header at the top of the
backplane PCB
Orange remote tracking header.
Pin 1 is the pin closest to the phase
bars (left side of the rack as you look
in)
Position A - Primary
Position B - Secondary
An indicator lamp
50mA 24Vdc max for
internal power supply
- Sensor3 CE Rack (ESR3 Series) 1
- Installation Manual 1
- Table of Contents 3
- Appendix A 4
- Appendix B 4
- Appendix C 4
- Warnings 5
- Warnings v 7
- Introduction 9
- Contacting ETC 10
- Prepare for Installation 11
- Where to Mount the Rack 12
- Dimmer Room Requirements 12
- Wire Routing 12
- Installation of Racks 13
- 2 Installation of Racks 7 15
- CAUTION: 16
- 2 Installation of Racks 9 17
- 2 Installation of Racks 11 19
- Rack Cabling Access 19
- Connect Line Power Wiring 20
- Land Load Wires 21
- WARNING: 22
- Cut Key Slots for Modules 23
- 3 Land Load Wires 17 25
- Control and Data Connections 27
- Running DMX Cable to Racks 28
- Figure 22: IDC DMX Connection 29
- Running Ethernet to Racks 30
- 1 2 3 4+24Vdc COM 32
- Station Connection (Optional) 33
- Finishing Installation 35
- Sealing Rack Air Leaks 36
- Attaching the door 36
- 5 Finishing Installation 29 37
- 5 Finishing Installation 31 39
- Installing Dimmer Modules 40
- Completing Installation 40
- 5 Finishing Installation 33 41
- Emergency Modules 44
- C Emergency Modules 37 45
Powiązane produkty i podręczniki dla Czujniki Etc Sensor3 CE (ESR3) Rack
Czujniki Etc CEM3 v1.5.1 Instrukcja Użytkownika
(76 strony)
(76 strony)
Czujniki Etc CEM3 v1.5.0 Instrukcja Użytkownika
(78 strony)
(78 strony)
Czujniki Etc CEM3 v1.5.0 Instrukcja Użytkownika
(80 strony)
(80 strony)
Miele H4780BP Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ofen Miele H4780BP.
Wir stellen 1 PDF-Handbücher Miele H4780BP zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentarze do niniejszej Instrukcji